How to Root Galaxy S3 I9300 on Android 4.3 XXUGML3 Jelly Bean Firmware

The international version of Samsung Galaxy S3 (GT-I9300) has already received the latest Android 4.3 Jelly Bean update with base firmware I9300XXUGML3. The new official firmware is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Samsung Galaxy S3 I9300 users who have already updated their devices with Android 4.3 XXUGML3 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by Senior Recognized XDA-Developers, Chainfire. Head over to the CF-Auto-Root main thread to learn more about the root method.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Drivers for Samsung Galaxy S3 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S3 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The CF-Auto-Root file works only on the international version of Samsung Galaxy S3 (GT-I9300). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S3 by navigating to Settings >> About Phone.

Files Required
1. CF-Auto-Root for Galaxy S3 I9300 (CF-Auto-Root-m0-m0xx-gti9300.zip)
2. Odin 3.07 (Mirror Link)

Steps to Root Galaxy S3 I9300 Running on Android 4.3 XXUGML3 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using WinRAR/7-Zip/WinZip or any other extracting tool.
Step 2: Switch off the Galaxy S3. Then boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer as an Administrator.
Step 4: Connect the Galaxy S3 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 5: In Odin, click the PDA button and select the CF-Auto-Root-m0-m0xx-gti9300.tar.md5 file.
Step 6: Verify that Auto Reboot and F. Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option is NOT selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from the computer.

Samsung Galaxy S3 I9300 running on Android 4.3 XXUGML3 Jelly Bean is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

How to Root Galaxy S4 Mini (Verizon) SCH-I435 on Android 4.2.2 Jelly Bean Without Tripping the KNOX Warranty Void Counter

Samsung Galaxy S4 Mini (Verizon) SCH-I435 users who wish to root their devices running on Android 4.2.2 Jelly Bean, may follow the tutorial below.

This tutorial uses Root Exploit package released by Senior XDA-Developers, k1mu. The Root Exploit package allows Galaxy S4 Mini users to root their devices easily without tripping the KNOX warranty void counter.

Disclaimer: We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Note: This method will NOT set the KNOX warranty void flag. It will set the "Custom" flag, but that's nothing to worry about. Tested working on the Galaxy S4 Mini (Verizon) SCH-I435 with Android 4.2.2 VRUAMK5 Jelly Bean.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy S4 Mini on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 percent.
5. The Root Exploit package works only on the Verizon version of the Galaxy S4 Mini (SCH-I435). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 Mini by navigating to Settings >> About Phone.

File Required
1. Root Exploit (saferoot.zip) - Mirror Link

Steps to Root Galaxy S4 Mini (Verizon) SCH-I435 Running on Android 4.2.2 Jelly Bean
Step 1: Extract the Root Exploit package to the computer using WinRAR/7-Zip/WinZip or any other extracting tool.
Step 2: Connect the Galaxy S4 Mini to the computer using USB cable.
Step 3: On the computer, navigate to the extracted directory and double click "install.bat" file. You will see command prompt window which will detect your device and automatically run the scripts.

If you are using Linux or Mac OS X, navigate to the extracted directory in a terminal window and type "sh ./install.sh".

Step 4: Follow the on-screen instructions. Once the rooting procedure completes, your phone will reboot automatically.

That's it! Samsung Galaxy S4 Mini (Verizon) SCH-I435 with Android 4.2.2 Jelly Bean is now rooted successfully. Open the app drawer of the phone and check for an app called SuperSU. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Note: Many Samsung devices store a flash counter that keeps track of how many times you have flashed custom firmwares to your device. Triangle Away can be used to reset the flash counter to zero.

How to Fix "Unfortunately, SuperSU has stopped"?
Step 1: Download and install the latest APK of SuperSU on your device.
Step 2: Open SuperSU app (update the binary if prompted) and allow it to disable KNOX.
Step 3: Reboot your device.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

How to Update Galaxy S3 Mini I8190 with Android 4.1.2 DXAML1 Jelly Bean Official Firmware

Samsung has just released the latest Android 4.1.2 Jelly Bean update with firmware build number I8190DXAML1 for Galaxy S3 Mini users in Southeast Asian countries. The new official firmware is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: I8190DXAML1
CSC: I8190QLBAML1
MODEM: I8190DXAML1
Version: Android 4.1.2
Build date: Dec 27, 2013
Regions: Indonesia, Malaysia, Philippines, Singapore, Vietnam, Thailand

Samsung Galaxy S3 Mini I8190 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy S3 Mini on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S3 Mini should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The Android 4.1.2 DXAML1 Jelly Bean firmware is compatible only with Samsung Galaxy S3 Mini (GT-I8190). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S3 Mini by navigating to Settings >> About Phone.

Files Required
1. Android 4.1.2 DXAML1 Jelly Bean Firmware (Mirror Link)
2. Odin 3.07 (Mirror Link)

Steps to Update Galaxy S3 Mini I8190 with Android 4.1.2 DXAML1 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy S3 Mini.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S3 Mini to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 7: Select the following files in Odin from extracted I8190DXAML1 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from the computer.

Samsung Galaxy S3 Mini I8190 should be now updated with official Android 4.1.2 DXAML1 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S3 Mini I8190 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data

How to Update Galaxy S3 I9300 with Android 4.3 XXUGNA5 Jelly Bean Official Firmware

Samsung has rolled out a new software update for the international version of Galaxy S3 (GT-I9300). The new software update is still based on Android 4.3 Jelly Bean and now available for Galaxy S3 users in Switzerland as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: I9300XXUGNA5
CSC: I9300AUTGNA1
MODEM: I9300XXUGMK6
Version: Android 4.3
Build date: Jan 16, 2014
Regions: Switzerland

Samsung Galaxy S3 I9300 users who missed the OTA update notification or unable to access the update over Samsung KIES, can now download and install the same manually using our step-by-step guide.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy S3 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S3 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The Android 4.3 XXUGNA5 Jelly Bean firmware is compatible only with the international version of Galaxy S3 (GT-I9300). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S3 by navigating to Settings >> About Phone.

Files Required
1. Android 4.3 XXUGNA5 Jelly Bean Firmware (Mirror Link 1, Link 2, Link 3) for Galaxy S3 I9300
2. Odin 3.07 (Mirror Link)

Steps to Update Galaxy S3 I9300 with Android 4.3 XXUGNA5 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy S3.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S3 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 7: Select the following files in Odin from extracted I9300XXUGNA5 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from the computer.

Samsung Galaxy S3 I9300 should be now updated with Android 4.3 XXUGNA5 Jelly Bean official firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S3 I9300 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

How to Root Galaxy S3 I9300 on Android 4.3 XXUGNA5 Jelly Bean Firmware

Samsung has released another Android 4.3 Jelly Bean update with firmware build number I9300XXUGNA5 for the international version of Galaxy S3 (GT-I9300). The new official firmware is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Samsung Galaxy S3 I9300 users who have already updated their devices with Android 4.3 XXUGNA5 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by Senior Recognized XDA-Developers, Chainfire. Head over to the CF-Auto-Root main thread to learn more about the root method.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Drivers for Samsung Galaxy S3 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S3 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The CF-Auto-Root file works only on the international version of Samsung Galaxy S3 (GT-I9300). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S3 by navigating to Settings >> About Phone.

Files Required
1. CF-Auto-Root for Galaxy S3 I9300 (CF-Auto-Root-m0-m0xx-gti9300.zip)
2. Odin 3.07 (Mirror Link)

Steps to Root Galaxy S3 I9300 Running on Android 4.3 XXUGNA5 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using WinRAR/7-Zip/WinZip or any other extracting tool.
Step 2: Switch off the Galaxy S3. Then boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer as an Administrator.
Step 4: Connect the Galaxy S3 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 5: In Odin, click the PDA button and select the CF-Auto-Root-m0-m0xx-gti9300.tar.md5 file.
Step 6: Verify that Auto Reboot and F. Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option is NOT selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from the computer.

Samsung Galaxy S3 I9300 running on Android 4.3 XXUGNA5 Jelly Bean is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

How to Update Galaxy Tab 3 7.0 (Wi-Fi) SM-T210 with Android 4.1.2 XXAML4 Jelly Bean Official Firmware

Samsung Galaxy Tab 3 7.0 with model number SM-T210 has officially received the latest Android 4.1.2 Jelly Bean update with firmware build number T210XXAML4. The new official firmware is now available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: T210XXAML4
CSC: T210ILOANA2
MODEM: T210XXAML4
Version: Android 4.1.2
Build date: Dec 23, 2013
Regions: Israel

Samsung Galaxy Tab 3 7.0 (Wi-Fi) SM-T210 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Tab 3 7.0 on the computer.
2. Enable USB Debugging Mode on the device by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Tab 3 7.0 should be factory unlocked.
5. Ensure the battery of the device is charged more than 80 percent.
6. The Android 4.1.2 XXAML4 Jelly Bean firmware is compatible only with the Wi-Fi version of the Galaxy Tab 3 7.0 (SM-T210). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Tab 3 7.0 by navigating to Settings >> About Phone.

Files Required
1. Android 4.1.2 XXAML4 Jelly Bean Firmware (Mirror Link)
2. Odin 3.07 (Mirror Link)

Steps to Update Galaxy Tab 3 7.0 (Wi-Fi) SM-T210 with Android 4.1.2 XXAML4 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off Galaxy Tab 3 7.0.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Tab 3 7.0 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 7: Select the following files in Odin from extracted T210XXAML4 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process completes, your device will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from the computer.

Samsung Galaxy Tab 3 7.0 (Wi-Fi) SM-T210 should be now updated with the Android 4.1.2 XXAML4 Jelly Bean official firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Tab 3 7.0 (Wi-Fi) SM-T210 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

How to Update Galaxy Tab 3 10.1 (Wi-Fi) P5210 with Android 4.2.2 XXUANA4 Jelly Bean Official Firmware

The Wi-Fi version of Samsung Galaxy Tab 3 10.1 (GT-P5210) has received the latest Android 4.2.2 Jelly Bean update with firmware build number P5210XXUANA4. The new official update is now available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: P5210XXUANA4
CSC: P5210OJVANA1
MODEM: P5210XXUANA4
Version: Android 4.2.2
Build date: Jan 22, 2013
Regions: Tunisia, Egypt, Iran, Iraq, Kenya, Morocco, Pakistan, Saudi Arabia, Turkey, United Arab Emirates

Samsung Galaxy Tab 3 10.1 (Wi-Fi) P5210 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Tab 3 10.1 on the computer.
2. Enable USB Debugging Mode on the device by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Tab 3 10.1 should be factory unlocked.
5. Ensure the battery of the device is charged more than 80 percent.
6. The Android 4.2.2 XXUANA4 Jelly Bean firmware is compatible only with the Wi-Fi version of Galaxy Tab 3 10.1 (GT-P5210). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Tab 3 10.1 by navigating to Settings >> About Phone.

Files Required
1. Android 4.2.2 XXUANA4 Jelly Bean Firmware for Galaxy Tab 3 10.1 (Wi-Fi) P5210
2. Odin 3.07 (Mirror Link)

Other regions: Israel

Steps to Update Galaxy Tab 3 10.1 (Wi-Fi) P5210 with Android 4.2.2 XXUANA4 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off Galaxy Tab 3 10.1.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Tab 3 10.1 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 7: Select the following files in Odin from extracted P5210XXUANA4 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process completes, your device will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from the computer.

Samsung Galaxy Tab 3 10.1 (Wi-Fi) P5210 should be now updated with the Android 4.2.2 XXUANA4 Jelly Bean official firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Tab 3 10.1 (Wi-Fi) P5210 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

How to Update Galaxy Fame S6810B with Android 4.1.2 VJAML2 Jelly Bean Official Firmware

Samsung recently released the latest Android 4.1.2 Jelly Bean update with base firmware S6810BVJAML2 for the Brazilian version of Galaxy Fame (GT-S6810B). The new official firmware is now available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: S6810BVJAML2
CSC: S6810BZTOAML1
MODEM: S6810BVJAML1
Version: Android 4.1.2
Build date: Dec 17, 2013
Regions: Brazil

Samsung Galaxy Fame S6810B users who missed the OTA update notification or unable to access the update over Samsung KIES, can now download and install the same manually using our step-by-step guide.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Fame on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Fame should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The Android 4.1.2 VJAML2 Jelly Bean firmware is compatible only with Samsung Galaxy Fame (GT-S6810B). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Fame by navigating to Settings >> About Phone.

Files Required
1. Android 4.1.2 VJAML2 Jelly Bean Firmware (Mirror Link) for Galaxy Fame S6810B
2. Odin 3.07 (Mirror Link)

Steps to Update Galaxy Fame S6810B with Android 4.1.2 VJAML2 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy Fame.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Fame to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 7: Select the following files in Odin from extracted S6810BVJAML2 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect it from the computer.

Samsung Galaxy Fame S6810B should be now updated with Android 4.1.2 VJAML2 Jelly Bean official firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Fame S6810B stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

how to Update Galaxy Fame S6810L with Android 4.1.2 UBANA1 Jelly Bean Official Firmware


The Latin America version of Samsung Galaxy Fame with model number GT-S6810L has already received the latest Android 4.1.2 Jelly Bean Over-The-Air (OTA) update with firmware build number S6810LUBANA1. The new official firmware is currently available for users in Argentina.

Firmware details
PDA: S6810LUBANA1
CSC: S6810LPSPANA2
MODEM: S6810LUBAML1
Version: Android 4.1.2
Build date: Jan 02, 2014
Regions: Argentina

Samsung Galaxy Fame S6810L users who missed the OTA update notification or unable to access the update over Samsung KIES, can now download and install the same manually using our step-by-step guide.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Fame on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Fame should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The Android 4.1.2 UBANA1 Jelly Bean firmware is compatible only with Samsung Galaxy Fame (GT-S6810L). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Fame by navigating to Settings >> About Phone.

Files Required
1. Android 4.1.2 UBANA1 Jelly Bean Firmware for Galaxy Fame S6810L
2. Odin 3.07 (Mirror Link)

Steps to Update Galaxy Fame S6810L with Android 4.1.2 UBANA1 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy Fame.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Fame to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 7: Select the following files in Odin from extracted S6810LUBANA1 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect it from the computer.

Samsung Galaxy Fame S6810L should be now updated with Android 4.1.2 UBANA1 Jelly Bean official firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Fame S6810L stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

How to Update Galaxy Trend Lite S7390 with Android 4.1.2 XWUANA2 Jelly Bean Official Firmware

Samsung Galaxy Trend Lite (GT-S7390) also known as Galaxy Fresh has received Android 4.1.2 Jelly Bean update with firmware build number S7390XWUANA2. The new official firmware is now available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: S7390XWUANA2
CSC: S7390QXEANA1
MODEM: S7390XWUANA2
Version: Android 4.1.2
Build date: Jan 17, 2014
Regions: Russia, Kazakhstan, Ukraine, Uzbekistan (La Fleur)

Samsung Galaxy Trend Lite S7390 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Trend Lite on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Trend Lite should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The Android 4.1.2 XWUANA2 Jelly Bean firmware is compatible only with Samsung Galaxy Trend Lite (GT-S7390). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Trend Lite by navigating to Settings >> About Phone.

Files Required
1. Android 4.1.2 XWUANA2 Jelly Bean Firmware for Galaxy Trend Lite S7390
2. Odin 3.07 (Mirror Link)

Steps to Update Galaxy Trend Lite S7390 with Android 4.1.2 XWUANA2 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy Trend Lite.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Trend Lite to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 7: Select the following files in Odin from extracted S7390XWUANA2 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect it from the computer.

Samsung Galaxy Trend Lite S7390 should be now updated with official Android 4.1.2 XWUANA2 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Trend Lite S7390 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

How to Update Galaxy Trend Plus S7580 with Android 4.2.2 XXUAML4 Jelly Bean Official Firmware

Samsung has begun rolling out the Android 4.2.2 Jelly Bean update for Galaxy Trend Plus (GT-S7580). The new official firmware is now available for download in select European countries as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: S7580XXUAML4
CSC: S7580OXXAML4
MODEM: S7580XXUAMK8
Version: Android 4.2.2
Build date: Dec 17, 2013
Regions: Greece

Samsung Galaxy Trend Plus S7580 users who missed the OTA update notification or unable to access the update over Samsung KIES, can now download and install the same manually using our step-by-step guide.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Trend Plus on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Trend Plus should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The Android 4.2.2 XXUAML4 Jelly Bean firmware is compatible only with the Galaxy Trend Plus (GT-S7580). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Trend Plus by navigating to Settings >> About Phone.

Files Required
1. Android 4.2.2 XXUAML4 Jelly Bean Firmware (Mirror Link) for Galaxy Trend Plus S7580
2. Odin 3.07 (Mirror Link)

Steps to Update Galaxy Trend Plus S7580 with Android 4.2.2 XXUAML4 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy Trend Plus.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Trend Plus to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 7: Select the following files in Odin from extracted S7580XXUAML4 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from the computer.

Samsung Galaxy Trend Plus S7580 should be now updated with Android 4.2.2 XXUAML4 Jelly Bean official firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Trend Plus S7580 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

How to Root Galaxy Trend Plus S7580 on Android 4.2.2 Jelly Bean and Install CWM Recovery

Samsung Galaxy Trend Plus S7580 users who wish to root and install ClockworkMod (CWM) recovery on their devices, may follow our step-by-step guide.

This tutorial uses CWM recovery released by XDA-Developers member, djcliccone. The CWM recovery allows Galaxy Trend Plus users to root their devices without any difficulty.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-Requisites
1. Install USB Drivers for Samsung Galaxy Trend Plus on your computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Trend Plus should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The CWM recovery works only on the Galaxy Trend Plus (GT-S7580). Applying this on any incorrect variant might brick the device. Verify the model number of the Galaxy Trend Plus by selecting Settings >> About Phone.

Files Required
1. CWM (Mirror Link)
2. SuperSu (UPDATE-SuperSU-v1.34.zip) or the latest version
3. Odin 3.07 (Mirror Link)

Steps to Install CWM Recovery on Galaxy Trend Plus S7580
Step 1: Extract the CWM recovery and Odin 3.07 files using WinRAR/7-Zip/WinZip or any other extracting tool.
Step 2: Copy the SuperSU .zip file to the SD card of your phone.
Step 3: Switch off the Galaxy Trend Plus. Then boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 4: Run Odin on the computer as an Administrator.
Step 5: Connect the Galaxy Trend Plus to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 6: In Odin, click the PDA button and select the recovery.tar.md5 file. Verify that F. Reset Time, Auto Reboot and Re-Partition options are NOT selected.
Step 7: Double-check and click Start button in Odin. The installation process will now begin.
Step 8: Once the installation process completes, you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from the computer and then go to Step 9.

Steps to Root Galaxy Trend Plus S7580 via CWM Recovery
Step 9: Boot the device into CWM recovery by pressing and holding Volume Up, Home and Power buttons together.
Step 10: In CWM recovery, select "install zip from sdcard" and then select "choose zip from sdcard". Now, navigate to the SuperSU .zip file that you copied earlier and confirm the installation by selecting Yes.
Step 11: Once the installation process completes, return to main recovery menu and select "reboot system now".

Samsung Galaxy Trend Plus S7580 running on Android 4.2.2 Jelly Bean is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Screenshot: Install CWM recovery via Odin

Thank's to all fellas at XDA who first tried out this rooting technique. This root method was originally posted via XDA-Developers original thread.

How to Update Galaxy Grand Duos I9082 with Android 4.2.2 XXUBNA5 Jelly Bean Official Firmware

Samsung Galaxy Grand with Dual SIM card slot also known as Galaxy Grand Duos (GT-I9082) has just received the latest Android 4.2.2 Jelly Bean update with firmware build number I9082XXUBNA5. The new official firmware is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: I9082XXUBNA5
CSC: I9082OJVBNA2
MODEM: I9082XXUBNA2
Version: Android 4.2.2
Build date: Jan 22, 2014
Regions: Iraq, Algeria, Afghanistan, Egypt, Iran, Kenya, Morocco, Pakistan, Saudi Arabia, South Africa, Turkey, Tunisia, United Arab Emirates

Samsung Galaxy Grand Duos I9082 users who missed the OTA update notification or unable to access the update over Samsung KIES, can now download and install the same manually using our step-by-step guide.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Grand Duos on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Grand Duos should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The Android 4.2.2 XXUBNA5 Jelly Bean firmware is compatible only with the Galaxy Grand Duos (GT-I9082). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Grand Duos by navigating to Settings >> About Phone.

Files Required
1. Android 4.2.2 XXUBNA5 Jelly Bean Firmware (Mirror Link) for Galaxy Grand Duos I9082
2. Odin 3.07 (Mirror Link)

Steps to Update Galaxy Grand Duos I9082 with Android 4.2.2 XXUBNA5 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy Grand Duos.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Grand Duos to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 7: Select the following files in Odin from extracted I9082XXUBNA5 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from the computer.

Samsung Galaxy Grand Duos I9082 should be now updated with Android 4.2.2 XXUBNA5 Jelly Bean official firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Grand Duos I9082 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

How to Update Galaxy Tab 3 7.0 SM-T211 with Android 4.1.2 XXANA1 Jelly Bean Official Firmware

Samsung has rolled out the latest Android 4.1.2 Jelly Bean update for for the 3G + Wi-Fi version of Galaxy Tab 3 7.0 (SM-T211). The new official firmware is now available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: T211XXANA1
CSC: T211OJVANA2
MODEM: T211XXAMGM
Version: Android 4.1.2
Build date: Jan 07, 2013
Regions: Algeria, Afghanistan, Egypt, Iran, Iraq, Kenya, Morocco, Pakistan, Saudi Arabia, South Africa, Tunisia, United Arab Emirates

Samsung Galaxy Tab 3 7.0 SM-T211 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Tab 3 7.0 on the computer.
2. Enable USB Debugging Mode on your tablet by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Tab 3 7.0 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the tablet is charged more than 80 percent.
6. The Android 4.1.2 XXANA1 Jelly Bean firmware is compatible only with the 3G + Wi-Fi version of Galaxy Tab 3 7.0 (SM-T211). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Tab 3 7.0 by navigating to Settings >> About Phone.

Files Required
1. Android 4.1.2 XXANA1 Jelly Bean Firmware (Mirror Link) for Galaxy Tab 3 7.0 SM-T211
2. Odin 3.07 (Mirror Link)

Steps to Update Galaxy Tab 3 7.0 SM-T211 with Android 4.1.2 XXANA1 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off Galaxy Tab 3 7.0.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Tab 3 7.0 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 7: Select the following files in Odin from extracted T211XXANA1 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process is completed, your device will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your tablet from the computer.

Samsung Galaxy Tab 3 7.0 SM-T211 should be now updated with the Android 4.1.2 XXANA1 Jelly Bean official firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Tab 3 7.0 SM-T211 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

How to Update Galaxy Tab Pro 8.4 (Wi-Fi) SM-T320 with Android 4.4.2 XXU1ANB6 KitKat Official Firmware

The Wi-Fi version of Samsung Galaxy Tab Pro 8.4 (SM-T320) has received a new Android 4.4.2 KitKat update with firmware build number T320XXU1ANB6. The new official firmware is now available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: T320XXU1ANB6
CSC: T320OLB1ANB3
MODEM: T320XXU1ANB6
Version: Android 4.4.2
Build date: Feb 22, 2014
Regions: Singapore, Philippines

Samsung Galaxy Tab Pro 8.4 (Wi-Fi) SM-T320 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Tab Pro 8.4 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 percent.
5. The Android 4.4.2 XXU1ANB6 KitKat firmware is compatible only with the Wi-Fi version of Galaxy Tab Pro 8.4 (SM-T320). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Tab Pro 8.4 by navigating to Settings >> About Phone.

Files Required
1. Android 4.4.2 XXU1ANB6 KitKat Firmware (Mirror Link)
2. Odin 3.07 (Mirror Link)

Steps to Update Galaxy Tab Pro 8.4 (Wi-Fi) SM-T320 with Android 4.4.2 XXU1ANB6 KitKat Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy Tab Pro 8.4.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Tab Pro 8.4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Step 7: Select the following files in Odin from extracted T320XXU1ANB6 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect it from the computer.

Samsung Galaxy Tab Pro 8.4 (Wi-Fi) SM-T320 should be now updated with Android 4.4.2 XXU1ANB6 KitKat official firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Tab Pro 8.4 (Wi-Fi) SM-T320 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

How to Update Galaxy S4 (LTE) I9505 with Android 4.4.2 VJUFNB2 KitKat Official Firmware

Samsung has just released another Android 4.4.2 KitKat update for the Snapdragon variant of Galaxy S4 (GT-I9505). The new official firmware is currently available for users in Brazil as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: I9505VJUFNB2
CSC: I9505ZTOFNB3
MODEM: I9505VJUFNB2
Version: Android 4.4.2
Build date: Feb 18, 2014
Regions: Brazil

Samsung Galaxy S4 (LTE) I9505 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy S4 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 percent.
5. The Android 4.4.2 VJUFNB2 KitKat firmware is compatible only with the LTE version of Samsung Galaxy S4 (GT-I9505). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

Files Required
1. Android 4.4.2 VJUFNB2 KitKat Firmware (Mirror Link)
2. Odin 3.07 (Mirror Link)

Steps to Update Galaxy S4 (LTE) I9505 with Android 4.4.2 VJUFNB2 KitKat Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy S4.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Step 7: Select the following files in Odin from extracted I9505VJUFNB2 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect it from the computer.

Samsung Galaxy S4 (LTE) I9505 should be now updated with Android 4.4.2 VJUFNB2 KitKat official firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S4 (LTE) I9505 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

How to Root Galaxy Note 2 (Canadian) SGH-I317M on Android 4.3 Jelly Bean Without Tripping the KNOX Warranty Void Counter

Samsung Galaxy Note 2 (Canadian) SGH-I317M users who have already updated their devices with Android 4.3 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses Root Exploit package released by Senior XDA-Developers, k1mu. The Root Exploit package allows Galaxy Note 2 users to root their devices easily without tripping the KNOX warranty void counter.

Disclaimer: We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Note: This method will NOT set the KNOX warranty void flag. It will set the "Custom" flag, but that's nothing to worry about.

Pre-requisites
1. Install USB Drivers for Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone. Go to Settings >> About Phone. Tap on Build Number several times till the message shows "You are now a Developer". Then enable USB debugging by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 percent.
5. The Root Exploit package works only on the Canadian version of the Galaxy Note 2 (SGH-I317M). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. Root Exploit (saferoot.zip) - Mirror Link

Steps to Root Galaxy Note 2 (Canadian) SGH-I317M Running on Android 4.3 Jelly Bean
Step 1: Extract the Root Exploit package to the computer using WinRAR/7-Zip/WinZip or any other extracting tool.
Step 2: Connect the Galaxy Note 2 to the computer using USB cable.
Step 3: On the computer, navigate to the extracted directory and double click "install.bat" file. You will see command prompt window which will detect your device and automatically run the scripts.
Step 4: Follow the on-screen instructions. Once the rooting procedure completes, your phone will reboot automatically.

That's it! Samsung Galaxy Note 2 (Canadian) SGH-I317M running on Android 4.3 Jelly Bean is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Note: Many Samsung devices store a flash counter that keeps track of how many times you have flashed custom firmwares to your device. Triangle Away can be used to reset the flash counter to zero.

How to Fix "Unfortunately, SuperSU has stopped"?
Step 1: Download and install the latest APK of SuperSU on your device.
Step 2: Open SuperSU app (update the binary if prompted) and allow it to disable KNOX.
Step 3: Reboot your device.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

How to Update Galaxy Note 3 (LTE) N9005 with Android 4.4.2 XXUENB7 KitKat Official Firmware

The Snapdragon variant of Samsung Galaxy Note 3 (SM-N9005) has received another Android 4.4.2 KitKat update with firmware build number N9005XXUENB7. The new official firmware is now available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: N9005XXUENB7
CSC: N9005DBTENB2
MODEM: N9005XXUENB1
Version: Android 4.4.2
Build date: Feb 27, 2014
Regions: Germany

Samsung Galaxy Note 3 (LTE) N9005 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Note 3 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 3 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The Android 4.4.2 XXUENB7 KitKat firmware is compatible only with the LTE version of Samsung Galaxy Note 3 (SM-N9005). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 3 by navigating to Settings >> About Phone.

Files Required
1. Android 4.4.2 XXUENB7 KitKat Firmware (Mirror Link)
2. Odin 3.07 (Mirror Link)

Steps to Update Galaxy Note 3 (LTE) N9005 with Android 4.4.2 XXUENB7 KitKat Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy Note 3.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 3 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Step 7: Select the following files in Odin from extracted N9005XXUENB7 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect it from the computer.

Samsung Galaxy Note 3 (LTE) N9005 should be now updated with Android 4.4.2 XXUENB7 KitKat official firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Note 3 (LTE) N9005 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

How to Update Galaxy S4 Mini I9190 with Android 4.2.2 XXUBNA1 Jelly Bean Official Firmware

Samsung has released another Android 4.2.2 Jelly Bean update with firmware build number I9190XXUBNA1 for Galaxy S4 Mini with model number GT-I9190. The new official firmware is now available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: I9190XXUBNA1
CSC: I9190SERBNA1
MODEM: I9190XXUBNA1
Version: Android 4.2.2
Build date: Jan 06, 2014
Regions: Russia

Samsung Galaxy S4 Mini I9190 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy S4 Mini on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 Mini should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The Android 4.2.2 XXUBNA1 Jelly Bean firmware is compatible only with the 3G version of the Samsung Galaxy S4 Mini (GT-I9190). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 Mini by navigating to Settings >> About Phone.

Files Required
1. Android 4.2.2 XXUBNA1 Jelly Bean Firmware (Mirror Link) for Galaxy S4 Mini I9190
2. Odin 3.07 (Mirror Link)

Steps to Update Galaxy S4 Mini I9190 with Android 4.2.2 XXUBNA1 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy S4 Mini.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S4 Mini to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.

Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.

Step 7: Select the following files in Odin from extracted I9190XXUBNA1 firmware folder:
  • Click the PDA button and select the .tar.md5 file.
  • Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
  • Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
  • Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect it from the computer.

Samsung Galaxy S4 Mini I9190 should be now updated with official Android 4.2.2 XXUBNA1 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S4 Mini I9190 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.